Google+
Showing posts with label technology. Show all posts
Showing posts with label technology. Show all posts

Friday, 20 June 2014

Welcome to DIY hub


Welcome Folks....
this blog is for the ones who likes to take their eagerness to their peak.....
so you can DO IT YOURSELF!!!

So we will be posting techno related posts from mobile development to Robotics and much more for your intrest...

We will b providing you best contents soon.. so stay at touch...
Read More


Friday, 30 August 2013

[DIY] MAKE your own Simple LASER alarm

If u r trying to find how to build a LASER ALARM to keep something secure...

HERE IS A SIMPLE GUIDE TO BUILD UR LASER ALARM



What you need :-


1. 2 small project boxes 
2. 1 1000uF 35v Capacitor 
3. 1 5K Variable Resistor 
4. Photocell 
5. IC Board 
6. 9v battery and clip 
7. 1 N3904 Transistor 
8. Toggle switch 
9. Small mirrors 
10. HandiTak 
11. 12v DC Piezo Siren - 102dB 
12. Aixiz 650nm 5mw 12X30mm laser 
13. Aixiz 3.2v AC Adapter


NOW FOLLOW THESE STEPS

Step 1: Build the Circuit :-



Build the circuit based on the diagram. I cut my IC board with a dremel to make it smaller so there was enough room in the box along with the 9 v battery.


Step 2: Install it :-



Install the circuit board and the 9v battery in the hobby box. Line up the photocell at the hole and hot glue everything in place. Also, attach the siren and run the wiring inside the box. Finish your solder connections with the siren.


Step 3: Build the Laser Housing :-


Cut 3 holes in your second hobby box. One for the switch, one for the laser housing and one small one for the wires from the AC Adapter. Run the wires from the AC adapter in the box. Install the swicth and hot glue the laser in place. Wire the positive end of the AC adapter to the red wire from the laser and wire the negative ends of the laser and adapter to the switch.

Step 4: Tweaking:-


Turn on the laser and point it at the photocell box. You will have to adjust the resistor so the photocell is sensitive to the laser pointing at it during the day. At night, when the laserbeam is broken, the siren will sound


Step 5: Mount the laser system:-


Decide where you want your protection, across what doorways and then decide on where you want the laser to plug in and where you want the photocell box to pick up the laser. I used 1" square mirrors (from an arts and crafts store) and HandiTak to mount the mirrors. You could use a more permanent solution for the mirrors. The idea is to angle all the mirrors to the next wall across where you want protection and then have it end up pointing at the photocell.







Now when it gets dark and the laserbeam is broken, the LOUD 102dB siren will wail!
Read More


Wednesday, 19 June 2013

[DIY] make your own WIFI SPYBOT

For making a wifi spybot the basic process involves stripping the R/C car, plugging in the Barracuda – which bridges the local servo controls with an ethernet connection – and hooking up the wireless router and webcam.  There’s also some fiddling with network settings to be done.




We will be showing you how to build a wifi robot / spybot from scratch. It is a very straight forward project and can easily be handled by a intermediate robot builder. To complete the robot, it will take a couple of hours.


WHAT U NEED FIRST-

1-Rc Car (new or used, choose one that could easily have a Rc servo fitted in the steering system. We got ours from Radio Shack.)


  • 1-Barracuda wifi robot controller
  • 1-Wifi Router 
  • 1-Network Camera
  • 2-Ethernet Cables
  • 1-5v Regulator for camera
  • 2-3 7.2v Rc Batteries (3300mAh or greater recommended)
  • Misc wire, solder, tape etc.




NOW follow some steps :-




Step 1: Hacking The Car





To start building your wifi Robot / spybot, gutting of the Rc car is the first step. Take out everything! We got our Rc truck from Radio Shack, but others will work also. We gutted it out and built a roll cage on top. Here is a Picture of the truck gutted and the 3 Rc batteries mounted in the truck.

The two red batteries are to power the main motor and the barracuda wifi controller. While the blue 7.2v battery will power the Linksys router, 5v Regulator for the camera, and the steering servo. Three batteries are not needed, but i just find that it makes the wifi robot / spybot more reliable and allows longer run times. If you opt for two batteries the Linksys router can handle 40v, so you will be fine running it straight off of the two packs. The same with the 5v regulator. Te only problem will be the power for the steering servo, so you will either have to add another 5v regulator and run it off of that or just get a higher amperage 5v Regulator and run the servo and the camera off of it. The latter would be easiest. 



Step 2: Install The Steering Servo



We gutted out the steering box and retro fitted in a standard Rc servo. Other people have used the steering Mechanism that comes with the Rc car, But I wanted true proportional steering.



Step 3: Install The Barracuda wifi robot / spybot controller











(Picture One)
We started this step out by extending the leads coming from the motor by soldering on extra wire we had laying around.

(Picture Two)
Here is a picture of the barracuda wifi robot / spybot controller. This is what we will be using to control our robot.

(Picture Three)
Here is a picture of the yellow lead from the motor connected to the terminal block. You can also see how the batteries are connected in series to power the barracuda wifi robot controller. On the green terminal block is where we connect the servo. The red wire is connected to the third 7.2v batteries ground and the servo's ground. The white wire is the servo's signal wire. The barracuda has two output ports. Each can individually be configured as a digital or analog input, digital output, or an Rc output making the Barracuda very flexible




 Step 4: Power the camera, router and servo



In this step, all we did was take the mating connector that will connect to the batteries connector and solder the power and ground together for the 5v regulator. The power plug for the Linksys and the power wires for the servo. For a more detailed view, check out our Youtube Video.
Here is a picture of the 5v Regulator attached to the rear battery.



 Step 5: connect everything to the router





 Configure your router to have the base Ip Address of 192.168.1.1. The stock Ip Address for the barracuda is 192.168.1.10. The IP can be changed to whatever you want it to be with the configuration program that comes with it. Connect the camera and the Barracuda wifi robot controller to the router using the two Ethernet cables. Configure the camera to have an ip that works with that of the router and barracuda.


Step 6: Power up and go!


The barracuda wifi robot controller comes with a sample program and source code to drive the car. Power the car up,connect to your camera in the browser, run the sample program for the barracuda and start driving! The barracuda also supports use of a PS3 controller plugged into your computer to control it.


SOURCE - instructables

Read More


Monday, 8 April 2013

several ways of ROOTING Android device by Yourself

The most basic and important step during any type of development on android is, ROOTING it..
SO here are some ways so that u can root your device:-


Rooting Android with z4root :-

First, you’ll need to make sure that non-Market app installs are allowed; this is called sideloading apps. To do this, go to Menu > Settings > Applications and check “Unknown Sources”. (If it’s greyed out, that means that your carrier has decided to be mean and block sideloading. To remove this restriction, try rooting with SuperOneClick or device-specific rooting below.)

Now that your phone allows sideloading, download z4root onto your phone. Once it has been downloaded, use a file manager to navigate to the APK installer (it will probably be in the download folder) and install z4root. After it is installed, launch z4root from your app tray open it up from your launcher:


 Once z4root has been launched, you are half-way finished. Now all you have to do is decide if you want a permanent root, or just a root until you reboot your phone (temporary root). If you want a permanent root, be aware that it won’t work on every phone (try SuperOneClick or device-specific rooting if z4root doesn’t work for you).
Once you select what type of root you want, just follow on-screen instructions and you will be rooted within minutes. You know you are rooted if you have a “SuperUser” app in your app tray. You may have to reboot your device for this to appear. If the “SuperUser” app appears, congrats! Your Android 2.2 phone is now rooted.
Te following is the list of known phones compatible/incompatible with the permanent root:



If your phone is not in the list shown above, it may or may not be compatible with z4root. The only way to find out is try it out. If your phone is on the incompatible list, you can only use the temporary root option.




Rooting with SuperOneClick :-

Rooting with SuperOneClick is a fairly easy affair, but requires a bit of setup first. The first thing you need to do is make sure your device will work with SuperOneClick. It is most likely compatible if it is not one of these (the following are incompatible devices)
  • Sprint EVO 4G (HTC Supersonic)
  • Droid Incredible (HTC Incredible)
  • HTC Desire GSM
  • HTC Desire CDMA (HTC BravoC)
  • HTC Aria
  • Droid Eris (HTC DesireC)
  • HTC Wildfire (HTC Buzz)
These phones have locked NAND chips. In order to remove this lock, you must use unrevoked, a NAND unlocker.
So far the known phones that are compatible with SuperOneClick are:
  • Acer Liquid Metal
  • Dell Streak
  • HTC Magic (Sapphire) 32B
  • HTC Bee
  • LG Ally
  • Motorola Atrix 4G
  • Motorola Charm
  • Motorola Cliq
  • Motorola Droid
  • Motorola Flipside
  • Motorola Flipout
  • Motorola Milestone
  • Nexus One
  • Samsung Captivate
  • Samsung Galaxy 551 (GT-I5510)
  • Samsung Galaxy Portal/Spica I5700
  • Samsung Galaxy S 4G
  • Samsung Galaxy S I9000
  • Samsung Galaxy S SCH-I500
  • Samsung Galaxy Tab
  • Samsung Transform M920
  • Samsung Vibrant
  • Sony Ericsson Xperia E51i X8
  • Sony Ericsson Xperia X10
  • Sprint Hero
  • Telus Fascinate
  • Toshiba Folio 100
The key thing to note is just because your phone is not on the above list does not mean SuperOneClick won’t work with your phone. As long as your phone is not listed on the incompatible list (first list shown above), then your phone may still work with SuperOneClick. The only way you will know for sure is to give it a try; if you are on Android 2.3 Gingerbread or lower, SuperOneClick will likely work for your device. Use other method if ur device isnt compatible.
After verifying your phone is rootable, there still remain couple of prerequisites to rooting your device:
  • You NEED to put your phone on USB Debugging mode
  • You NEED to install make sure the Android drivers for your phone are installed
  • Make sure you DO NOT mount your SD card
  • If you still can’t get something to run, try doing it in recovery mode
To put your device into USB Debugging mode, go to Settings > Applications > Development and check the “USB Debugging” box. After enabling debugging, install drivers for your phone on your computer and plug in your phone.
After installing the drivers, you’ll need to download SuperOneClick. Note that, due to the exploit used in the rooting program, it may be detected as a virus; this is to be expected and the program is clean as far as we know.Open SuperOneClick.exe (Vista + 7: right click -> run as administrator):



The beauty of SuperOneClick is its rooting method is universal, allowing for all Android devices to be rooted at any version number. So, just hit Root to root your device.
(Sidenote: After rooting, if your device did not allow for sideloading, you can enable sideloading on your device by hitting the Allow Non-Market Apps buttons.)
Once the root procedure has finished, go back to your device. Open your app launcher and you should a new app called “Superuser”. This verifies your device has been rooted; if you don’t see it, try rebooting your device.




Other :-

If z4root nor SuperOneClick worked for your device and we haven’t covered your device , the best place to find how to root your device is XDA-Developers. Visit XDA and look for your specific device; then roam the forums and look for a thread that explains how to root. (You will most likely find it in the Android Development subforum for your device.) You can even ask questions if you have trouble.


Read More


Join Us

//go.ad2up.com/afu.php?id=25365

© Copyright 2012, Design by Lord HTML.
​